How to print greeting cards at home
19 October 2026
How to lay out the front, back and inside of a card, what to print each size on, and how to fold it cleanly.
A home printer makes good greeting cards when the card size suits the paper. An A5 card prints on a whole A4 sheet, and an A6 card on an A5 card blank. In the US, an A9 card prints on a whole Letter sheet, and an A2 card on a half-Letter blank.
Design the front of the card at its folded size. The card sizes guide lists each one in millimetres, inches and pixels.
Laying out the outside and the inside
A card that opens from the side is printed flat, on a sheet twice its width. The outside goes on one side of the sheet, with the back on the left and the front on the right. The back usually carries your shop name and the card’s title, set small near the bottom.
The inside goes on the other side of the same sheet. Its left half is the inside of the front cover, and the message usually goes on the right.
To print both sides, turn the sheet over side to side, like the page of a book. On most printers that’s the “flip on short edge” setting for a landscape page. Print one test sheet and fold it before you print the rest.
A card that opens from the bottom is folded along the top, so it’s printed on a sheet twice its height. The front goes on the bottom half and the back on the top half.
Mock My Work takes either the front on its own or the whole outside file, without bleed. From the whole file it uses the right half as the front, or the bottom half for a card folded along the top.

Choosing the paper
To print one card at a time with nothing to trim, print on a sheet the card’s flat size. A5 and A9 cards are a standard sheet. For the other sizes, card blanks come pre-cut and scored to the flat size, usually with matching envelopes:
| Card | Flat size | Print on |
|---|---|---|
| A6 | 210 × 148 mm | An A6 card blank, which is A5 |
| A5 | 296 × 210 mm | A4 |
| 5 × 7 in | 254 × 178 mm | A 5 × 7 in card blank |
| 145 mm square | 290 × 145 mm | A 145 mm square card blank |
| A2 | 8½ × 5½ in | An A2 card blank, half a Letter sheet |
| A9 | 11 × 8½ in | US Letter |
Card blanks are smaller than the paper a printer usually takes, so check yours has a custom paper size and a feed for small sheets. Without one, print on A4 or Letter and trim the card to its flat size.
Printing to the edge
Most home printers stop a few millimetres short of the edge of the sheet, which leaves a white border round the card. If yours does, plan the design for it. Keep the background the colour of the card, or give the design a border of its own.
Some printers, often inkjet photo printers, can print borderless, with colour right to the edge of the sheet. Check whether yours offers it for the paper size and type you use, since many only do it on photo paper. Borderless printing enlarges the design a little so it runs off the sheet, which crops a few millimetres from every edge. Keep text inside the safe area.
If your printer can’t print borderless, a print shop can print the cards with colour to the edge. Its template will ask for bleed. That’s extra background past the edge of the card, usually 3 mm on every side (⅛ in in the US), which the shop cuts off.
Card weight and folding
Shop-bought greeting cards are often 300 gsm or heavier, which is more than most home printers take. A printer’s headline limit, often 300 g/m², is usually for the maker’s own photo paper, and the limit for card is lower. HP’s ENVY 6000 printers, for example, take cards up to 200 g/m². Look for the card figure in your printer’s specifications, and try one sheet before you buy a pack. If the printer has a rear or manual feed, use that, since card bends less on the way through.
Score the fold line before you fold, with a bone folder or the back of a craft knife against a ruler. Then fold with the grain of the card where you can. Folded across the grain, the surface can crack, and the crack shows most where ink covers the fold.